Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
This great article following next on the subject of A Step-by-Step Guide to Installing a Bathtub is especially remarkable. Check it out yourself and figure out what you think of it.
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately difficult job. If the old tub is readily easily accessible, the project can relocate speedily; if you have to open a wall to remove the old tub as well as position the new tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also set in the brand-new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you might need a professional plumber to make tube connections.
This short article will help you mount a new tub in your restroom if you have already purchased a new bathtub and don't need to change the arrangement of your previous water supply pipes.
Your devices and also product list must consist of the following:
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of removing the existing faucets can be quite troublesome due to the restricted gain access to that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, place the tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water as well as examine all joints and also new pipework for leakages and also tighten them if necessary. Load the bathtub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait until the bathtub has been used at the very least when as this will certainly resolve it into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in location between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The previous kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in difficulties with moisture and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and installations. They are sold in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed reading the new blog posting. In case you enjoyed reading our article if you please do not forget to pass it around. I love reading our article about How to Install a Bathtub Yourself.
Free Quote
Report this page